Administrative Code

Virginia Administrative Code
4/18/2024

Part I. Definitions

9VAC5-510-10. General.

A. For the purpose of this chapter or any orders issued by the board, the words or terms shall have the meanings given them in 9VAC5-510-20.

B. Unless specifically defined in the Virginia Air Pollution Control Law or in this chapter, terms used shall have the meaning given them by 9VAC5-10-20 (general definitions, Regulations for the Control and Abatement of Air Pollution), 9VAC5-170-20 (definitions, Regulation for General Administration), or commonly ascribed to them by recognized authorities, in that order of priority.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-20. Terms defined.

"Actual emissions" means the actual emissions of a pollutant from a stationary source or emissions unit reflecting the rate, in tons per year, at which the source or unit actually emitted the pollutant during the most recent annual period. Actual emissions shall be calculated using the source or unit's actual operating hours, in place emission controls, production rates, and types of materials processed, stored, or combusted during the annual period. Valid continuous emission monitoring data or source test data shall be preferentially used to determine actual emissions. In the absence of valid continuous emissions monitoring data or source test data, the basis for determining actual emissions shall be any or all of the following as may be determined by the department: throughputs of process materials; throughputs of materials stored; usage of materials; data provided in manufacturer's product specifications, material volatile organic compound content reports or laboratory analyses; other information required by this chapter and other regulations of the board; or information requested in writing by the department. All calculations of actual emissions shall use U.S. Environmental Protection Agency or department-approved methods, including emission factors and assumptions.

"Annual period" means a period of 12 consecutive months determined on a rolling basis with a new 12-month period beginning on the first day of each calendar month.

"Federal operating permit" means a permit issued pursuant to Article 1 (9VAC5-80-50 et seq.) of Part II of 9VAC5 Chapter 80.

"Fugitive dust" means particulate matter composed of soil or other materials, or both, of natural origin. Fugitive dust may include emissions from haul roads, wind erosion of exposed surfaces and storage piles and other activities in which the material is either removed, stored, transported or redistributed.

"Fugitive emissions" means emissions which are generated by industrial or other activities and which do not pass through a stack, chimney, vent or other functionally equivalent opening, but which may escape from openings (such as windows, doors, ill-fitting closures or poorly maintained equipment) or material handling equipment.

"General permit" means the terms and conditions in Part IV (9VAC5-510-170 et seq.) of this chapter that meet the requirements of Part III (9VAC5-510-90 et seq.) of this chapter and issued under the provisions 9VAC5-80-1030 and 9VAC5-80-1250.

"New source review program" means a program for the preconstruction review and permitting of new stationary sources or emissions units or expansions to existing ones in accordance with regulations promulgated to implement the requirements of §§ 110(a)(2)(C), 112 (relating to permits for hazardous air pollutants), 165 (relating to permits in prevention of significant deterioration areas), and 173 (relating to permits in nonattainment areas) of the federal Clean Air Act.

"Nonmetallic mineral" means any of the following minerals or any mixture of which the majority is any of the following minerals:

1. Crushed and broken stone, including limestone, dolomite, granite, traprock, sandstone, quartz, quartzite, marl, marble, slate, shale, oil shale, and shell.

2. Sand and gravel.

3. Clay including kaolin, fireclay, bentonite, fuller's earth, ball clay, and common clay.

4. Rock salt.

5. Gypsum.

6. Sodium compounds, including sodium carbonate, sodium chloride, and sodium sulfate.

7. Pumice.

8. Gilsonite.

9. Talc and pyrophyllite.

10. Boron, including borax, kernite, and colemanite.

11. Barite.

12. Fluorospar.

13. Feldspar.

14. Diatomite.

15. Perlite.

16. Vermiculite.

17. Mica.

18. Kyanite, including andalusite, sillimanite, topaz, and dumortierite.

"Nonmetallic mineral processing facility" means any combination of equipment that is used to crush or grind any nonmetallic mineral wherever located, including lime plants, power plants, steel mills, asphalt concrete plants, portland cement plants, or any other facility processing nonmetallic minerals. Includes activity at facilities where the primary purpose is classified as Standard Industrial Classification (SIC) Code 1411, 1422, 1423, 1429, 1442, 1446, 1455, 1459, and 1499 as described in the Standard Industrial Classification Manual (see 9VAC5-20-21). Includes stationary diesel engines. Also includes activity at facilities classified under other SIC codes that may be colocated within the nonmetallic mineral processing area, unless they are expressly excluded by this chapter.

"Permittee" means the owner of a nonmetallic mineral processing facility covered under this general permit.

"Portable facility" means any nonmetallic mineral processing facility that is mounted on any chassis or skids and may be moved by the application of a lifting or pulling force. In addition, there shall be no cable, chain, turnbuckle, bolt or other means (except electrical connections) by which any piece of equipment is attached or clamped to any anchor, slab, or structure, including bedrock that must be removed prior to the application of a lifting or pulling force for the purpose of transporting the unit.

"Potential to emit" means the maximum capacity of a stationary source to emit any air pollutant under its physical and operational design. Any physical or operational limitation on the capacity of a source to emit an air pollutant, including air pollution control equipment and restrictions on hours of operation or on the type or amount of material combusted, stored, or processed, shall be treated as part of its design if the limitation is state and federally enforceable.

"Relocation" means a change in physical location of a nonmetallic mineral processing facility or an emissions unit from one nonmetallic mineral processing facility to another nonmetallic mineral processing facility.

"Spreadsheet" means the Aggregate Processing Emission Calculation Spreadsheet and the Stationary Diesel Engine Emission Calculation Spreadsheet.

"State operating permit" means a permit issued pursuant to Article 5 (9VAC5-80-800 et seq.) of Part II of 9VAC5 Chapter 80.

Part II

General Provisions

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-30. Purpose and basis.

A. The purpose of the general permit is to require the owners of existing and new emissions units in the nonmetallic mineral processing industry to construct, modify, relocate and operate within the terms and conditions of a general permit that forms the legally enforceable basis for all regulatory and statutory requirements.

B. This general permit is being issued under the authority of 9VAC5-80-1030 and 9VAC5-80-1250.

C. This chapter does not require any owner to apply for coverage under the general permit but provides the opportunity for an owner to apply for coverage if the nonmetallic mineral processing facility meets the applicability criteria in 9VAC5-510-40 and all other requirements of this chapter.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-50. General.

A. The permittee shall operate the stationary source in conformance with all applicable regulations of the board.

B. Nonmetallic mineral processing facilities desiring authority to operate under the general permit shall register with the department as required under 9VAC5-20-160. For emissions units or groups of emissions units covered, the completion or updating of the spreadsheet shall be considered registration.

C. No provision of this chapter shall limit the power of the board to issue an operating permit pursuant to 9VAC5 Chapter 80 (9VAC5-80).

D. This chapter shall not relieve any stationary source from complying with the requirements of (i) any otherwise applicable permit issued under 9VAC5 Chapter 80 (9VAC5-80), (ii) any condition or term of any permit issued under 9VAC5 Chapter 80 (9VAC5-80), or (iii) any provision of a permit program. This chapter shall not preclude issuance of any permit with conditions or terms necessary to ensure compliance with this chapter.

E. For any nonmetallic mineral processing facility to be covered by the general permit, all equipment and emissions units at a stationary source that make up the nonmetallic mineral processing facility shall be covered by the general permit.

F. By the adoption of this chapter, the board confers upon the department the administrative, enforcement and decision making authority enumerated herein.

G. The promulgating of amendments to this regulation shall invalidate any authorization to operate under the general permit one year after the effective date of the amendments. Owners may reapply for authorization to operate under the amended general permit and the department may grant the authorization to operate as provided in 9VAC5-510-150.

H. Any decisions of the board or department made pursuant to this chapter may be appealed pursuant to 9VAC5-170-200, § 10.1-1318 of the Virginia Air Pollution Control Law, and the Administrative Process Act.

I. This general permit may not be used to meet the requirements of 9VAC5-80-120.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-70. Circumvention.

A. No owner or other person shall cause or permit the installation or use of any device or any means which, without resulting in reduction in the total amount of air pollutants emitted, conceals or dilutes an emission of air pollutants which would otherwise violate this chapter. Such concealment includes, but is not limited to, either of the following:

1. The use of gaseous diluents to achieve compliance with a visible emissions standard or with a standard which is based on the concentration of a pollutant in gases discharged to the atmosphere.

2. The piecemeal carrying out of an operation to avoid coverage by a standard that applies only to operations larger than a specified size.

B. This section does not prohibit the construction of a stack.

C. Regardless of the exemptions provided in this chapter, permits shall be required of owners who circumvent the requirements of this chapter by causing or allowing a pattern of ownership or development over a geographic area of a source which, except for the pattern of ownership or development, would otherwise require a permit.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-90. Requirements for granting an authorization to operate under the general permit.

A. The department may grant an authorization to operate under the general permit for a source that meets the applicability criteria in 9VAC5-510-40. The authorization to operate may include an authorization to construct, modify and relocate the source operating under the general permit.

B. After the initial authorization to construct, modify, relocate and operate under the general permit has been granted for a nonmetallic mineral processing facility, new and modified emissions units at the facility may operate under the general permit in accordance with the terms and conditions of the general permit.

C. Stationary sources or emissions units subject to the general permit shall comply with all requirements applicable to other permits issued under 9VAC5 Chapter 80 (9VAC5-80).

D. The general permit is issued in accordance with § 2.2-4006 A 9 of the Administrative Process Act.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-110. Required information for initial applications.

A. The department will furnish application forms to applicants. The information required by this section shall be determined and submitted according to procedures and methods acceptable to the department.

B. Each initial application for coverage under the general permit shall include, but not be limited to, the following:

1. Information specified in 9VAC5-510-130 A.

2. Additional information that the department deems necessary to implement and enforce other requirements of the regulations of the board or to determine the applicability of such requirements.

3. Any additional information or documentation that the department deems necessary to review and analyze the air pollution aspects of the source.

4. A certification of compliance with all applicable requirements by a responsible official.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-130. Application statement and notice of termination forms.

A. The required statement for initial applications shall be in the following form:

NONMETALLIC MINERAL PROCESSING GENERAL PERMIT

APPLICATION STATEMENT

(please print or type)

1. Name of company:

2. Name of owner:

3. Name of plant:

4. Mailing address:

5. Plant site manager or contact:

6. Telephone number:

7. Registration number:

(new sites leave blank)

8. Project name:

9. Description of activity (minerals processed):

10. Primary standard industrial classification (SIC) code:

Secondary SIC codes:

11. County:

12. Location:

13. A spreadsheet and a plant layout or flow diagram for all emissions units at the nonmetallic mineral processing facility for which the application is submitted. The following information shall be included for each piece of equipment:

a. The total rated crushing capacity for all primary crushers at the facility.

b. A description of the equipment, including applicability of any standard of performance under 40 CFR Part 60, as follows:

(1) Widths of belt conveyors.

(2) Dimensions of the top screen and configuration (e.g., triple deck) of the screening unit.

(3) Rated capacity (ton/hr) of each crusher.

(4) Rated capacity (ton or ton/hr) of all other equipment not exempt from new source review program requirements.

c. A unique ID number.

d. The date the equipment was manufactured.

e. The dates any required performance testing was conducted and submitted to the regional director.

f. Total rated horsepower of all stationary diesel engines.

g. Maximum hours of operation or gallons of fuel to be consumed, for each stationary diesel engine.

h. A description and accounting of all emissions of regulated air pollutants from all emissions units or groups of emissions units. Emissions shall be determined in a manner acceptable to the department. Fugitive emissions shall be included in the application as provided in the spreadsheet.

14. Calculations on which the information in subdivision 14 h of this subsection is based to the extent not covered in the spreadsheet. Any calculations shall include sufficient detail to permit assessment of the validity of the calculations and to enable the department to verify the actual emissions and potential to emit for the stationary source. This may include, but not be limited to, the following:

a. Actual and potential emissions in tons per annual period for each emissions unit or group of emission units.

b. Information needed to determine emissions as follows: fuels, fuel use, raw materials, production rates, loading rates, and operating schedules.

c. Identification and description of air pollution control equipment and compliance monitoring devices or activities.

15. Attach to this application an aerial photo or scale map which clearly shows the property boundaries and plant site.

Certification:

"I certify under penalty of law that this document and all attachments were prepared under my direction or supervision in accordance with a system designed to assure that qualified personnel properly gather and evaluate the information submitted. Based on my inquiry of the person or persons who manage the system, or those persons directly responsible for gathering and evaluating the information, the information submitted is, to the best of my knowledge and belief, true, accurate, and complete. I am aware that there are significant penalties for submitting false information, including the possibility of fine and imprisonment for knowing violations."

Signatures: Date:

Signatures: Date:

Name of persons signing above: (printed or typed)

(printed or typed)

Titles:

For Department use only:

Accepted/Not accepted by: Date:

Required attachments:

1. Local government certification form (greenfield sites only)

2. Spreadsheet and a plant layout or flow diagram

3. Aerial photo or scale map

B. The required notice of termination shall be in the following form:

NONMETALLIC MINERAL PROCESSING GENERAL PERMIT

NOTICE OF TERMINATION

1. Nonmetallic mineral processing general permit number:

2. Reason for termination request (Choose one):

a. The emissions associated with facility have been eliminated.

b. The facility authorized by the general permit has been determined to be shutdown in accordance with 9VAC5-20-220.

c. A permit has been issued for the facility covered by the general permit issued under the provisions of 9VAC5 Chapter 80 (9VAC5-80).

3. On what date do you wish coverage under this general permit to terminate?

4. Facility owner

Name:

Mailing address:

City: State: Zip code:

Phone:

5. Facility location

Name:

Address:

City: State: Zip code:

6. Certification:

"I certify under penalty of law that all emissions associated with the identified facility have been eliminated, that the facility authorized by the general permit has been determined to be shutdown in accordance with 9VAC5-20-220, or that a permit has been issued covering the facility under the provisions of 9VAC5 Chapter 80 (9VAC5-80). I understand that by submitting this notice of termination, I am no longer authorized to operate under the general permit. I also understand that the submittal of this notice of termination does not release an owner from liability for any violations of this permit under the Air Pollution Control Law."

Signatures: Date:

Date:

Name of persons signing above: (printed or typed)

(printed or typed)

Titles:

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002; amended, Virginia Register Volume 40, Issue 5, eff. October 23, 2023.

9VAC5-510-150. Granting an authorization to operate under the general permit.

A. The department will grant authorization to operate under the conditions and terms of the general permit to sources that meet the applicability criteria set forth in 9VAC5-510-40.

B. Granting an authorization to operate under the general permit to a nonmetallic mineral processing facility covered by the general permit is not subject to the public participation procedures under § 2.2-4006 A 9 of the Administrative Process Act.

C. A response to each application for coverage under the general permit will be provided within 30 days.

D. Nonmetallic mineral processing facilities covered under a general permit will be issued a letter, a certificate, or any other document which would attest that the facility is authorized to operate under the general permit. The document will be accompanied by a copy of the general permit and the application submitted by the permittee.

E. The letter, certificate or other document, along with the copy of the general permit, application and 40 CFR Part 60, subpart OOO, shall be retained by the department and at the stationary source.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-170. General permit.

Any owner whose application is accepted by the director will receive the following permit and shall comply with the requirements in it and be subject to all requirements of this chapter and the regulations of the board.

General Permit No.: Air510

Effective date: December 1, 2002

GENERAL PERMIT FOR NONMETALLIC MINERAL PROCESSING

In compliance with the provisions of the Air Pollution Control Law and regulations adopted pursuant to it, owners of nonmetallic mineral processing facilities are authorized to operate under the authority of this permit, except those where board regulations or policies prohibit such operation.

This general permit covers all owners of activities located at nonmetallic mineral processing facilities where the primary purpose is classified as Standard Industrial Classifications 1411, 1422, 1423, 1429, 1442, 1446, 1455, 1459, and 1499.

The authorization to operate under this permit shall be in accordance with this cover page, 9VAC5-510-180—General Terms and Conditions, 9VAC5-510-190—Emission Standards, 9VAC5-510-200—Compliance Determination and Verification by Emission Testing, 9VAC5-510-210—Compliance Determination and Verification by Emission Monitoring, 9VAC5-510-220—Recordkeeping Requirements, 9VAC5-510-230—Reporting Requirements, 9VAC5-510-240—Compliance Certifications, and 9VAC5-510-250—Enforcement, as specified in 9VAC5-510-180 through 9VAC5-510-250.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002; Errata, 19:7 VA.R. 1119 December 16, 2002.

9VAC5-510-190. Emissions standards.

A. The permittee shall not cause or allow to be discharged into the atmosphere from any covered emissions units any visible emissions in excess of the limits specified in subdivisions 1, 2 and 3 of this subsection.

1. Equipment manufactured or fabricated on or prior to August 31, 1983, shall not exceed an opacity of 20% when averaged over a six-minute period.

2. Equipment manufactured or fabricated after August 31, 1983, shall comply with 40 CFR Part 60, Subpart 000, 9VAC5-50-260 and the following standards:

a. Crushing: primary and secondary—15% opacity, tertiary—7% opacity.

b. Screening, conveyor transfers, and surge bins—10% opacity.

c. Fabric filter exhausts—7% opacity.

d. Wash plants—no visible emissions from wet screening and subsequent processing up to next crusher or storage bin.

3. Other nonspecific emission points including loadout and stationary diesel engines are limited to 10% opacity.

4. The opacity standards prescribed under this subsection shall apply at all times except during periods of startup, shutdown, malfunction, and as otherwise provided in the applicable standard. This subdivision shall apply only to (i) emission units, the construction, modification or relocation of which commenced on or after March 17, 1972; and (ii) emission units, the reconstruction of which commenced on or after December 10, 1976.

B. The permittee shall not cause or allow to be discharged into the atmosphere from any covered emissions units any particulate matter in excess of the limits specified in subdivisions 1 and 2 of this subsection.

1. Fabric filter exhausts controlling equipment manufactured or fabricated on or prior to August 31, 1983, shall not exceed the following limits:

a. For facilities located in AQCR 7, the limits in Table 510A (ref: 9VAC5-40-270).

b. For facilities located in the remainder of the Commonwealth, 0.05 grains/dscf (ref: Article 14 (9VAC5-40-1820 et seq.) of 9VAC5 Chapter 40).

TABLE 510A


    Process Weight Rate       Maximum Allowable Emission Rate 


                                                              


  Lb/Hr          Tons/Hr                   Lb/HR              


100            0.050                        0.46              


150            0.075                        0.66              


200            0.100                        0.85              


250            0.125                        1.03              


300            0.150                        1.20              


350            0.175                        1.35              


400            0.200                        1.50              


450            0.225                        1.63              


500            0.250                        1.77              


550            0.275                        1.85              


600            0.300                        2.01              


650            0.325                        2.12              


700            0.350                        2.24              


750            0.375                        2.34              


800            0.400                        2.43              


850            0.425                        2.53              


900            0.450                        2.62              


950            0.475                        2.72              


1000           0.500                        2.80              


1100           0.55                         2.97              


1200           0.60                         3.12              


1300           0.65                         3.26              


1400           0.70                         3.40              


1500           0.75                         3.54              


1600           0.80                         3.66              


1700           0.85                         3.79              


1800           0.90                         3.91              


1900           0.95                         4.03              


2000           1.00                         4.14              


2100           1.05                         4.24              


2200           1.10                         4.34              


2300           1.15                         4.44              


2400           1.20                         4.55              


2500           1.25                         4.64              


2600           1.30                         4.74              


2700           1.35                         4.84              


2800           1.40                         4.92              


2900           1.45                         5.02              


3000           1.50                         5.10              


3100           1.55                         5.18              


3200           1.60                         5.27              


3300           1.65                         5.36              


3400           1.70                         5.44              


3500           1.75                         5.52              


3600           1.80                         5.61              


3700           1.85                         5.69              


3800           1.90                         5.77              


3900           1.95                         5.85              


4000           2.00                         5.93              


4100           2.05                         6.01              


4200           2.10                         6.08              


4300           2.15                         6.15              


4400           2.20                         6.22              


4500           2.25                         6.30              


4600           2.30                         6.37              


4700           2.35                         6.45              


4800           2.40                         6.52              


4900           2.45                         6.60              


5000           2.50                         6.67              


5500           2.75                         7.03              


6000           3.00                         7.37              


6500           3.25                         7.71              


7000           3.50                         8.05              


7500           3.75                         8.39              


8000           4.00                         8.71              


8500           4.25                         9.03              


9000           4.50                         9.36              


9500           4.75                         9.67              


10000          5.00                        10.00              


11000          5.50                        10.63              


12000          6.00                        11.28              


13000          6.50                        11.89              


14000          7.00                        12.50              


15000          7.50                        13.13              


16000          8.00                        13.74              


17000          8.50                        14.36              


18000          9.00                        14.97              


19000          9.50                        15.58              


20000          10.00                       16.19              


30000          15.00                       22.22              


40000          20.00                       28.30              


50000          25.00                       34.30              


60000 or more  30.00 or more               40.00              

2. Fabric filter exhausts controlling equipment manufactured or fabricated after August 31, 1983, shall not exceed 0.05 g/dscm (0.022 grains/dscf) (ref: 40 CFR Part 60, Subpart 000).

C. Fugitive dust/emissions controls shall include the following or equivalent as a minimum:

1. Fugitive dust/emissions from drills, stockpiles, material handling, screens, crushers, load-outs, and traffic areas shall be controlled by wet suppression or equivalent.

2. All material being stockpiled subject to windblown emissions shall be kept moist to control dust during storage and handling or covered at all times to minimize emissions.

3. Haul roads shall be controlled by wet suppression or equivalent.

4. Reasonable precautions shall be taken to prevent deposition of dirt on public roads and subsequent dust emissions. Materials spilled or tracked onto public paved surfaces shall be promptly removed to prevent particulate matter from becoming airborne.

D. In order to operate under the authority of this permit, a nonmetallic mineral processing facility shall not exceed any of the following:

1. The total rated crushing capacity for all primary crushers at the facility, including portable stone processing equipment temporarily located at the site, shall not exceed 5,000 tons per hour.

2. The total amount of fuel to be consumed by all stationary diesel engines, including portable equipment temporarily located at the site, shall not exceed 331,022 gallons of fuel per annual period.

3. The total actual emissions of any regulated pollutant from the stationary source shall not exceed 99 tons per annual period. Particulate matter emissions shall be used to determine compliance with this subdivision only if particulate matter (PM10) emissions cannot be quantified in a manner acceptable to the department.

E. The fuel used in stationary diesel engines shall be distillate oil or diesel fuel meeting ASTM specifications for No. 1 or No. 2 distillate oil or diesel fuel.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-200. Compliance determination and verification by emission testing.

A. The permittee may conduct emission tests, establish and maintain records, and make periodic emission reports as necessary to determine the actual emissions for the nonmetallic mineral processing facility.

B. Upon request of the department, the permittee shall conduct emission tests as are necessary to determine the type or amount or both of the pollutants emitted from the facility or whether the facility will be in compliance with 9VAC5-510-190 or any other provisions of any regulation of the board.

C. The emission testing conducted under this section shall be carried out in accordance with subdivisions 1 and 2 of this subsection or the provisions of 9VAC5 Chapters 40 9VAC5-40), 50 9VAC5-50) and 60 9VAC5-60), as applicable, or by other means acceptable to the department.

1. Visible emissions evaluations shall be conducted in accordance with 40 CFR Part 60, Subpart A, Method 9 or Method 22, as applicable.

2. Grain loading evaluations shall be conducted in accordance with 40 CFR Part 60, Subpart A, Method 5 or Method 17, as applicable.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-220. Recordkeeping requirements.

A. The permittee shall comply with the recordkeeping requirements in this section. The recordkeeping requirements of this permit shall not replace any recordkeeping requirement contained in other state or federal rules or regulations.

B. The permittee shall maintain records for each emission unit or groups of emission units sufficient to determine the actual emissions of the nonmetallic mineral processing facility. The permittee shall maintain records of emission data and operating parameters necessary to demonstrate compliance with this permit. These records shall be available for inspection by the department and shall be current for the most recent three years.

C. To meet the requirements of 9VAC5-510-210 with respect to recordkeeping, the permittee shall comply with the following:

1. Records of monitoring information shall include the following:

a. The date, place as defined in the authorization to operate under the general permit, and time of sampling or measurements.

b. The date or dates analyses were performed.

c. The company or entity that performed the analyses.

d. The analytical techniques or methods used.

e. The results of such analyses.

f. The operating conditions existing at the time of sampling or measurement.

2. Records of all monitoring data and support information shall be retained for at least three years from the date of the monitoring sample, measurement, report, or application. Support information includes all calibration and maintenance records and all original strip-chart recordings for continuous monitoring instrumentation, and copies of all reports required by the permit.

D. The recordkeeping requirements under this section shall be carried out in accordance with the provisions of 9VAC5 Chapters 40 (9VAC5-40), 50 (9VAC5-50) and 60 (9VAC5-60), as applicable, or by other means acceptable to the department.

E. In order to ensure the proper operation of air pollution control equipment, the permittee shall perform the following:

1. Develop a maintenance schedule and maintain records of all scheduled and nonscheduled maintenance to air pollution control equipment. These records shall be maintained on site for three years and shall be made available to department upon request.

2. Maintain an inventory of spare parts needed to minimize the duration of air pollution control equipment breakdowns.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

9VAC5-510-240. Compliance.

A. The department will evaluate a nonmetallic mineral processing facility's compliance with the emission standards in 9VAC5-510-190 as part of the department's annual compliance process. In performing the evaluation, the department will consider any annual emission update submitted pursuant to 9VAC5-510-230.

B. Upon presentation of credentials and other documents as may be required by law, the permittee shall allow the department to perform the following:

1. Enter upon the premises where the source is located or emissions-related activity is conducted, or where records must be kept under the terms and conditions of the permit.

2. Have access to and copy, at reasonable times, any records that must be kept under the terms and conditions of the permit.

3. Inspect at reasonable times any facilities, equipment (including monitoring and air pollution control equipment), practices, or operations regulated or required under the permit.

4. Sample or monitor at reasonable times substances or parameters for the purpose of assuring compliance with the permit or applicable requirements.

Department representatives will report to the site office and notify a company official or representative of their presence immediately upon entering any operation, as required by Mine Safety and Health Agency standards. For purposes of this condition, the time for inspection shall be deemed reasonable during regular business hours or whenever the facility is in operation. Nothing contained herein shall make an inspection time unreasonable during an emergency.

Statutory Authority

§ 10.1-1308 of the Code of Virginia.

Historical Notes

Derived from Virginia Register Volume 19, Issue 3, eff. December 1, 2002.

Website addresses provided in the Virginia Administrative Code to documents incorporated by reference are for the reader's convenience only, may not necessarily be active or current, and should not be relied upon. To ensure the information incorporated by reference is accurate, the reader is encouraged to use the source document described in the regulation.

As a service to the public, the Virginia Administrative Code is provided online by the Virginia General Assembly. We are unable to answer legal questions or respond to requests for legal advice, including application of law to specific fact. To understand and protect your legal rights, you should consult an attorney.